3200威尼斯vip(中国)有限公司

News
NEWS
Home News Industry News
Complete CCK-8 experiment operation steps, save them quickly!
2023-09-15

CCK-8 is a cell biology experiment widely used for cell proliferation and cytotoxicity. CCK-8 solution can be added directly to cell samples without the need to pre-prepare various components. The more and faster the cells proliferate, the darker the cell color, proving that the toxicity is low; the greater the cytotoxicity, the lighter the color. For the same cells, the depth of color (the amount of formazan produced) and the number of cells show a linear relationship.





Cells, 96-well cell culture plate, CO2incubator, ultra-clean workbench, micropipette, microplate reader, CCK-8 kit, etc.

1. Take cells in good growth condition and prepare a cell suspension of a certain concentration, add 100 ul per well to a 96-well cell culture plate. Usually, for cell proliferation experiments, add 2×10³ cells/100 ul per well, and for cytotoxicity experiments, add 5×10³ cells/100 ul per well (the specific number of cells used per well needs to be determined based on factors such as cell size and cell proliferation speed).If they are adherent cells, pre-culture in a 37°C incubator for 2-6 hours until the cells adhere before carrying out the experiment; if they are suspension cells, pre-culture is not required.。

2. According to experimental requirements, add 0-10 ul of the test sample to the culture wells and continue culturing for an appropriate time. If performing a cytotoxicity test, the culture time after adding the toxic substance needs to be explored. It depends on the properties of the toxic substance and the sensitivity of the cells, and generally should be determined according to the cell cycle, at least 1-2 generations or more.

3. Take 10 ul of CCK-8 solution and add it to the 96-well cell culture plate, then continue incubating in a 37°C incubator for 0.5-4 hours.


4. Measure the absorbance. It is recommended to use dual wavelengths for measurement, with a detection wavelength of 430-490 nm and a reference wavelength of 600-650 nm, or use a single wavelength of 450 nm for detection.




Calculation formula cell viability=[(As-Ab) / (Ac-Ab)] × 100%Inhibition rate=[(Ac-As) / (Ac-Ab)] × 100% As: absorbance of experimental wells (containing cells, culture medium, CCK-8 solution, and drug solution); Ac: absorbance of control wells (containing cells, culture medium, and CCK-8 solution, without drug); Ab: absorbance of blank wells (containing culture medium and CCK-8 solution, without cells or drug) 
1. If the initial culture volume of the cells is 200 ul, then 20 ul of CCK-8 solution needs to be added, and so on.

2. It is recommended to set 3 replicate wells for each drug concentration and finally take the average to make the curve.

3. Design the experimental controls well and try to eliminate interference from other factors: 1) Blank control: wells with the same amount of cell culture medium, CCK-8 solution, and drug but no cells; 2) Negative control: cell wells with no drug but with drug solvent added.

4. The detection of the kit depends on reactions catalyzed by dehydrogenases. If the test substance is oxidizing or reducing, it may interfere with the detection and must be removed by some means (replace with fresh culture medium before adding CCK-8 solution to remove the influence of the drug. If the influence of the drug is relatively small, the culture medium may not be replaced, and the blank absorbance after adding the drug to the culture medium can be directly subtracted).

5. Pay attention to the incubation time after adding CCK-8 solution. The length of incubation depends on experimental conditions such as cell type and cell density. In the initial experiment, detection can be performed with a microplate reader at 0.5, 1, 2, and 4 hours respectively, and then a time point with a more suitable absorbance range can be selected for subsequent experiments.

6. When cells are cultured in an incubator, the outermost wells of the culture plate are prone to drying and evaporation, which increases error due to inaccurate volume. In general, only culture medium is added to the outermost ring of wells, and they are not used as measurement wells.。

7. If the OD value is not measured temporarily, 10 ul of 10% SDS solution can be added to each well to terminate the reaction, and the culture plate should be covered and stored away from light at room temperature. If measured within 24 hours, the absorbance will not change much, but immediate detection is generally still recommended.

8. Before detection with a microplate reader, ensure that there are no bubbles in each well, otherwise it will interfere with the measurement.



Share to:
Products
Cell Biology
Molecular Biology
Liquid Handling
Bioprocessing
Custom Products
Solutions
Biopharmaceuticals
Cell & Gene Therapy
Vaccines
Diagnostics & Testing
About Us
Company Profile
Corporate Culture
Development History
Honors & Qualifications
Contact Us
Service Hotline: 400-800-6815
Email: info@cellprobio.net
Address: Building 40, No. 18 Dongchang Road, Suzhou Industrial Park
[WeChat Account QR Code]
Copyright © 2023 Suzhou CellPro Biotechnology Co., Ltd. All rights reserved. Record No.:Su ICP No. 19059453-1
Baidu
sogou